subroutine SetGCMR( Spec, QGC )


    ! USE statements
    !

    ! ヒストリデータ出力
    ! History data output
    !
    use gtool_historyauto, only: HistoryAutoAddVariable, HistoryAutoPut

    ! 時刻管理
    ! Time control
    !
    use timeset, only: TimeN, TimesetClockStart, TimesetClockStop

    ! 時系列データの読み込み
    ! Reading time series
    !
    use read_time_series, only: SetValuesFromTimeSeriesWrapper


    character(*), intent(in ):: Spec
    real(DP)    , intent(out):: QGC


    !
    ! Work variables
    !


    ! 初期化確認
    ! Initialization check
    !
    if ( .not. set_gcmr_inited ) then
      call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
    end if


    ! 計算時間計測開始
    ! Start measurement of computation time
    !
    call TimesetClockStart( module_name )


    if ( Spec == 'CO2' ) then

      if ( CO2File == '' ) then
        QGC = MRCO2
      else
        call SetValuesFromTimeSeriesWrapper( "CO2", CO2File, CO2Name, QGC )
      end if

    else if ( Spec == 'N2O' ) then

      if ( N2OFile == '' ) then
        QGC = MRN2O
      else
        call SetValuesFromTimeSeriesWrapper( "N2O", N2OFile, N2OName, QGC )
      end if

    else if ( Spec == 'CH4' ) then

      if ( CH4File == '' ) then
        QGC = MRCH4
      else
        call SetValuesFromTimeSeriesWrapper( "CH4", CH4File, CH4Name, QGC )
      end if

    end if


    call HistoryAutoPut( TimeN, "CO2", QGC )
    call HistoryAutoPut( TimeN, "N2O", QGC )
    call HistoryAutoPut( TimeN, "CH4", QGC )


    ! 計算時間計測一時停止
    ! Pause measurement of computation time
    !
    call TimesetClockStop( module_name )


  end subroutine SetGCMR

  subroutine SetGCMRInit


    ! ファイル入出力補助
    ! File I/O support
    !
    use dc_iounit, only: FileOpen

    ! ヒストリデータ出力
    ! History data output
    !
    use gtool_historyauto, only: HistoryAutoAddVariable

    ! NAMELIST ファイル入力に関するユーティリティ
    ! Utilities for NAMELIST file input
    !
    use namelist_util, only: namelist_filename, NmlutilMsg, NmlutilAryValid


    !
    ! Work variables
    !
    integer:: unit_nml        ! NAMELIST ファイルオープン用装置番号.
                              ! Unit number for NAMELIST file open
    integer:: iostat_nml      ! NAMELIST 読み込み時の IOSTAT.
                              ! IOSTAT of NAMELIST read

    ! NAMELIST 変数群
    ! NAMELIST group name
    !
    namelist /set_gcmr_nml/ MRCO2, CO2File, CO2Name, MRN2O, N2OFile, N2OName, MRCH4, CH4File, CH4Name
          !
          ! デフォルト値については初期化手続 "set_gcmr#SetGCMRInit"
          ! のソースコードを参照のこと.
          !
          ! Refer to source codes in the initialization procedure
          ! "set_gcmr#SetGCMRInit" for the default values.
          !

    if ( set_gcmr_inited ) return


    ! デフォルト値の設定
    ! Default values settings
    !

!!$    MRCO2   = 382.0d-6     ! old default value
    MRCO2   =  369.0d-6 ! Value at 2000 in CMIP5 recommendation, PRE2005_MIDYR_CONC.DAT
    CO2File = ''
    CO2Name = ''
    MRN2O   =  316.0d-9 ! Value at 2000 in CMIP5 recommendation, PRE2005_MIDYR_CONC.DAT
    N2OFile = ''
    N2OName = ''
    MRCH4   = 1751.0d-9 ! Value at 2000 in CMIP5 recommendation, PRE2005_MIDYR_CONC.DAT
    CH4File = ''
    CH4Name = ''


    ! NAMELIST の読み込み
    ! NAMELIST is input
    !
    if ( trim(namelist_filename) /= '' ) then
      call FileOpen( unit_nml, namelist_filename, mode = 'r' ) ! (in)

      rewind( unit_nml )
      read( unit_nml, nml = set_gcmr_nml, iostat = iostat_nml )             ! (out)
      close( unit_nml )

      call NmlutilMsg( iostat_nml, module_name ) ! (in)
    end if


    call HistoryAutoAddVariable( "CO2", (/ 'time' /), "carbon dioxide", '1' )                  ! (in)
    call HistoryAutoAddVariable( "N2O", (/ 'time' /), "nitrous oxide", '1' )                   ! (in)
    call HistoryAutoAddVariable( "CH4", (/ 'time' /), "methane", '1' )                         ! (in)

    ! 印字 ; Print
    !
    call MessageNotify( 'M', module_name, '----- Initialization Messages -----' )
    call MessageNotify( 'M', module_name, '  MRCO2   = %f', d = (/ MRCO2 /) )
    call MessageNotify( 'M', module_name, '  CO2File = %c', c1 = trim( CO2File ) )
    call MessageNotify( 'M', module_name, '  CO2Name = %c', c1 = trim( CO2Name ) )
    call MessageNotify( 'M', module_name, '  MRN2O   = %f', d = (/ MRN2O /) )
    call MessageNotify( 'M', module_name, '  N2OFile = %c', c1 = trim( N2OFile ) )
    call MessageNotify( 'M', module_name, '  N2OName = %c', c1 = trim( N2OName ) )
    call MessageNotify( 'M', module_name, '  MRCH4   = %f', d = (/ MRCH4 /) )
    call MessageNotify( 'M', module_name, '  CH4File = %c', c1 = trim( CH4File ) )
    call MessageNotify( 'M', module_name, '  CH4Name = %c', c1 = trim( CH4Name ) )
    call MessageNotify( 'M', module_name, '-- version = %c', c1 = trim(version) )

    set_gcmr_inited = .true.

  end subroutine SetGCMRInit