| Class | lscond |
| In: |
lscond/lscond.f90
|
Note that Japanese and English are described in parallel.
大規模凝結過程によって温度と比湿を調節します.
Adjust temperature and specific humidity by a large scale condensation process.
Manabe, S., J. Smagorinsky, R. F. Strickler, Simulated climatology of a general circulation model with a hydrologic cycle, Mon. Wea. Rev., 93, 769-798, 1965.
| LScaleCond : | 温度と比湿の調節 |
| ———— : | ———— |
| LScaleCond : | Adjust temperature and specific humidity |
| Subroutine : | |||
| xyz_Temp(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_QVap(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_Press(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(in)
| ||
| xyr_Press(0:imax-1, 1:jmax, 0:kmax) : | real(DP), intent(in)
| ||
| xyz_DQH2OLiqDt(0:imax-1,1:jmax,1:kmax) : | real(DP), intent(out)
| ||
| FlagOutput : | logical , intent(in ), optional
|
大規模凝結スキームにより, 温度と比湿を調節します.
Adjust temperature and specific humidity by large scale condensation scheme.
subroutine LScaleCond( xyz_Temp, xyz_QVap, xyz_Press, xyr_Press, xyz_DQH2OLiqDt, FlagOutput )
!
! 大規模凝結スキームにより, 温度と比湿を調節します.
!
! Adjust temperature and specific humidity by
! large scale condensation scheme.
!
! モジュール引用 ; USE statements
!
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav, CpDry, LatentHeat, LatentHeatFusion
! $ L $ [J kg-1] .
! 融解の潜熱.
! Latent heat of fusion
! 時刻管理
! Time control
!
use timeset, only: DelTime, TimeN, TimesetClockStart, TimesetClockStop
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoPut
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only: xyz_CalcQVapSat, xyz_CalcDQVapSatDTemp
! 宣言文 ; Declaration statements
!
implicit none
real(DP), intent(inout):: xyz_Temp (0:imax-1, 1:jmax, 1:kmax)
! $ T $ . 温度. Temperature
real(DP), intent(inout):: xyz_QVap (0:imax-1, 1:jmax, 1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP), intent(in):: xyz_Press (0:imax-1, 1:jmax, 1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP), intent(in):: xyr_Press (0:imax-1, 1:jmax, 0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(out) :: xyz_DQH2OLiqDt(0:imax-1,1:jmax,1:kmax)
!
! Tendency of H2O liquid mixing ratio
logical , intent(in ), optional :: FlagOutput
!
! Flag for output
! 作業変数
! Work variables
!
real(DP):: xy_RainLsc (0:imax-1, 1:jmax)
! 降水量.
! Precipitation
real(DP):: xyz_DTempDtLsc (0:imax-1, 1:jmax, 1:kmax)
! 温度変化率.
! Temperature tendency
real(DP):: xyz_DQVapDtLsc (0:imax-1, 1:jmax, 1:kmax)
! 比湿変化率.
! Specific humidity tendency
real(DP):: xyz_QVapB (0:imax-1, 1:jmax, 1:kmax)
! 調節前の比湿.
! Specific humidity before adjust.
real(DP):: xyz_TempB (0:imax-1, 1:jmax, 1:kmax)
! 調節前の温度.
! Temperature before adjust.
!
real(DP):: xyz_QVapSat (0:imax-1, 1:jmax, 1:kmax)
! 飽和比湿.
! Saturation specific humidity.
real(DP):: xyz_DQVapSatDTemp(0:imax-1, 1:jmax, 1:kmax)
! $ \DD{q_{\rm{sat}}}{T} $
real(DP):: DelTemp
! 調節による温度変化量.
! Temperature variation by adjustment
real(DP):: LatentHeatLocal
!
! Latent heat used in this routine
integer:: i ! 経度方向に回る DO ループ用作業変数
! Work variables for DO loop in longitude
integer:: j ! 緯度方向に回る DO ループ用作業変数
! Work variables for DO loop in latitude
integer:: k ! 鉛直方向に回る DO ループ用作業変数
! Work variables for DO loop in vertical direction
integer:: itr ! イテレーション方向に回る DO ループ用作業変数
! Work variables for DO loop in iteration direction
real(DP):: xyz_RainLSC(0:imax-1, 1:jmax, 1:kmax)
real(DP):: TempBefAdj
real(DP):: QVapBefAdj
logical:: xyz_FlagSaturated(0:imax-1, 1:jmax, 1:kmax)
! 実行文 ; Executable statement
!
! 初期化確認
! Initialization check
!
if ( .not. lscond_inited ) then
call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
end if
! 計算時間計測開始
! Start measurement of computation time
!
call TimesetClockStart( module_name )
! 調節前 "QVap", "Temp" の保存
! Store "QVap", "Temp" before adjustment
!
xyz_QVapB = xyz_QVap
xyz_TempB = xyz_Temp
! 調節
! Adjustment
!
! 飽和比湿計算
! Calculate saturation specific humidity
!
xyz_QVapSat = xyz_CalcQVapSat( xyz_Temp, xyz_Press )
do k = 1, kmax
do j = 1, jmax
do i = 0, imax-1
if ( ( xyz_QVap(i,j,k) / xyz_QVapSat(i,j,k) ) >= CrtlRH ) then
xyz_FlagSaturated(i,j,k) = .true.
else
xyz_FlagSaturated(i,j,k) = .false.
end if
end do
end do
end do
! Set a value for latent heat
LatentHeatLocal = LatentHeat
do itr = 1, ItrtMax
! 飽和比湿計算
! Calculate saturation specific humidity
!
xyz_QVapSat = xyz_CalcQVapSat ( xyz_Temp, xyz_Press )
xyz_DQVapSatDTemp = xyz_CalcDQVapSatDTemp( xyz_Temp, xyz_QVapSat )
do k = 1, kmax
do j = 1, jmax
do i = 0, imax-1
! 飽和していたら, 温度と比湿の変化を計算
! Calculate tendency of temperature and humidity
! if moist is saturation.
!
if ( xyz_FlagSaturated(i,j,k) ) then
! 温度の変化分をニュートン法で求める
! Calculate variation of temperature
!
DelTemp = LatentHeatLocal * ( xyz_QVap(i,j,k) - CrtlRH * xyz_QVapSat(i,j,k) ) / ( CpDry + LatentHeatLocal * CrtlRH * xyz_DQVapSatDTemp(i,j,k) )
!=========
! check routine
!---------
!!$ TempBefAdj = xyz_Temp(i,j,k)
!!$ QVapBefAdj = xyz_QVap(i,j,k)
!=========
! 温度と比湿の調節
! Adjust temperature and specific humidity
!
xyz_Temp(i,j,k) = xyz_Temp(i,j,k) + DelTemp
!!$ xyz_QVap(i,j,k) = xyz_QVapSat(i,j,k) + xyz_DQVapSatDTemp(i,j,k) * DelTemp
xyz_QVap(i,j,k) = CrtlRH * ( xyz_QVapSat(i,j,k) + xyz_DQVapSatDTemp(i,j,k) * DelTemp )
!=========
! check routine
!---------
!!$ write( 6, * ) '====='
!!$ write( 6, * ) 'Energy difference before and after adjustment and each energy'
!!$ write( 6, * ) &
!!$ & CpDry * TempBefAdj + LatentHeatLocal * QVapBefAdj &
!!$ & - ( CpDry * xyz_Temp(i,j,k) + LatentHeatLocal * xyz_QVap(i,j,k) ), &
!!$ & CpDry * TempBefAdj + LatentHeatLocal * QVapBefAdj, &
!!$ & ( CpDry * xyz_Temp(i,j,k) + LatentHeatLocal * xyz_QVap(i,j,k) )
!=========
end if
end do
end do
end do
end do
! 比湿変化率, 温度変化率, 降水量の算出
! Calculate specific humidity tendency, temperature tendency,
! precipitation
!
xyz_DQVapDtLsc = ( xyz_QVap - xyz_QVapB ) / ( 2.0_DP * DelTime )
xyz_DTempDtLsc = ( xyz_Temp - xyz_TempB ) / ( 2.0_DP * DelTime )
xyz_DQH2OLiqDt = - xyz_DQVapDtLsc
! calculation for output
xy_RainLsc = 0.0_DP
do k = kmax, 1, -1
xy_RainLsc = xy_RainLsc + xyz_DQH2OLiqDt(:,:,k) * ( xyr_Press(:,:,k-1) - xyr_Press(:,:,k) ) / Grav
end do
! ヒストリデータ出力
! History data output
!
if ( .not. present( FlagOutput ) ) then
call HistoryAutoPut( TimeN, 'DTempDtLsc', xyz_DTempDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OVapDtLsc', xyz_DQVapDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OLiqDtLsc', xyz_DQH2OLiqDt )
else
if ( FlagOutput ) then
call HistoryAutoPut( TimeN, 'DTempDtLsc', xyz_DTempDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OVapDtLsc', xyz_DQVapDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OLiqDtLsc', xyz_DQH2OLiqDt )
end if
end if
! 計算時間計測一時停止
! Pause measurement of computation time
!
call TimesetClockStop( module_name )
end subroutine LScaleCond
| Subroutine : | |||
| xyz_Temp(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_QVap(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_QH2OLiq(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_QH2OSol(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_Press(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(in)
| ||
| xyr_Press(0:imax-1, 1:jmax, 0:kmax) : | real(DP), intent(in)
| ||
| xyz_DQH2OLiqDt(0:imax-1,1:jmax,1:kmax) : | real(DP), intent(out)
| ||
| xyz_DQH2OSolDt(0:imax-1,1:jmax,1:kmax) : | real(DP), intent(out)
| ||
| FlagOutput : | logical , intent(in ), optional
|
大規模凝結スキームにより, 温度と比湿を調節します.
Adjust temperature and specific humidity by large scale condensation scheme.
subroutine LScaleCond1D3DWrapper( xyz_Temp, xyz_QVap, xyz_QH2OLiq, xyz_QH2OSol, xyz_Press, xyr_Press, xyz_DQH2OLiqDt, xyz_DQH2OSolDt, FlagOutput )
!
! 大規模凝結スキームにより, 温度と比湿を調節します.
!
! Adjust temperature and specific humidity by
! large scale condensation scheme.
!
! モジュール引用 ; USE statements
!
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav
! $ g $ [m s-2].
! 重力加速度.
! Gravitational acceleration
! 時刻管理
! Time control
!
use timeset, only: DelTime, TimeN, TimesetClockStart, TimesetClockStop
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoPut
! 宣言文 ; Declaration statements
!
implicit none
real(DP), intent(inout):: xyz_Temp (0:imax-1, 1:jmax, 1:kmax)
! $ T $ . 温度. Temperature
real(DP), intent(inout):: xyz_QVap (0:imax-1, 1:jmax, 1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP), intent(inout):: xyz_QH2OLiq(0:imax-1, 1:jmax, 1:kmax)
! Specific liquid water content
real(DP), intent(inout):: xyz_QH2OSol(0:imax-1, 1:jmax, 1:kmax)
! Specific ice content
real(DP), intent(in):: xyz_Press (0:imax-1, 1:jmax, 1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP), intent(in):: xyr_Press (0:imax-1, 1:jmax, 0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(out) :: xyz_DQH2OLiqDt(0:imax-1,1:jmax,1:kmax)
!
! Tendency of H2O liquid mixing ratio
real(DP), intent(out) :: xyz_DQH2OSolDt(0:imax-1,1:jmax,1:kmax)
!
! Tendency of H2O ice mixing ratio
logical , intent(in ), optional :: FlagOutput
!
! Flag for output
! 作業変数
! Work variables
!
real(DP):: xy_RainLsc (0:imax-1, 1:jmax)
! 降水量.
! Precipitation
real(DP):: xyz_DTempDtLsc (0:imax-1, 1:jmax, 1:kmax)
! 温度変化率.
! Temperature tendency
real(DP):: xyz_DQVapDtLsc (0:imax-1, 1:jmax, 1:kmax)
! 比湿変化率.
! Specific humidity tendency
real(DP) :: z_Temp (1:kmax)
! $ T $ . 温度. Temperature
real(DP) :: z_QVap (1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP) :: z_QH2OLiq(1:kmax)
! Specic liquid water content
real(DP) :: z_QH2OSol(1:kmax)
! Specic ice content
real(DP) :: z_Press (1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP) :: r_Press (0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP) :: z_DQH2OLiqDt(1:kmax)
!
! Tendency of H2O liquid mixing ratio
real(DP) :: z_DQH2OSolDt(1:kmax)
!
! Tendency of H2O ice mixing ratio
integer:: i ! 経度方向に回る DO ループ用作業変数
! Work variables for DO loop in longitude
integer:: j ! 緯度方向に回る DO ループ用作業変数
! Work variables for DO loop in latitude
integer:: k ! 鉛直方向に回る DO ループ用作業変数
! Work variables for DO loop in vertical direction
! 実行文 ; Executable statement
!
! 初期化確認
! Initialization check
!
if ( .not. lscond_inited ) then
call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
end if
! 計算時間計測開始
! Start measurement of computation time
!
call TimesetClockStart( module_name )
do j = 1, jmax
do i = 0, imax-1
do k = 1, kmax
z_Temp (k) = xyz_Temp (i,j,k)
z_QVap (k) = xyz_QVap (i,j,k)
z_QH2OLiq(k) = xyz_QH2OLiq(i,j,k)
z_QH2OSol(k) = xyz_QH2OSol(i,j,k)
z_Press (k) = xyz_Press (i,j,k)
end do
do k = 0, kmax
r_Press (k) = xyr_Press (i,j,k)
end do
call LScaleCond1D( z_Temp, z_QVap, z_QH2OLiq, z_QH2OSol, z_Press, r_Press, z_DQH2OLiqDt, z_DQH2OSolDt )
do k = 1, kmax
xyz_Temp (i,j,k) = z_Temp (k)
xyz_QVap (i,j,k) = z_QVap (k)
xyz_QH2OLiq (i,j,k) = z_QH2OLiq (k)
xyz_QH2OSol (i,j,k) = z_QH2OSol (k)
xyz_DQH2OLiqDt(i,j,k) = z_DQH2OLiqDt(k)
xyz_DQH2OSolDt(i,j,k) = z_DQH2OSolDt(k)
end do
end do
end do
! calculation for output
xy_RainLsc = 0.0_DP
do k = kmax, 1, -1
xy_RainLsc = xy_RainLsc + xyz_DQH2OLiqDt(:,:,k) * ( xyr_Press(:,:,k-1) - xyr_Press(:,:,k) ) / Grav
end do
! ヒストリデータ出力
! History data output
!
if ( .not. present( FlagOutput ) ) then
call HistoryAutoPut( TimeN, 'DTempDtLsc', xyz_DTempDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OVapDtLsc', xyz_DQVapDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OLiqDtLsc', xyz_DQH2OLiqDt )
call HistoryAutoPut( TimeN, 'DQH2OSolDtLsc', xyz_DQH2OSolDt )
else
if ( FlagOutput ) then
call HistoryAutoPut( TimeN, 'DTempDtLsc', xyz_DTempDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OVapDtLsc', xyz_DQVapDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OLiqDtLsc', xyz_DQH2OLiqDt )
call HistoryAutoPut( TimeN, 'DQH2OSolDtLsc', xyz_DQH2OSolDt )
end if
end if
! 計算時間計測一時停止
! Pause measurement of computation time
!
call TimesetClockStop( module_name )
end subroutine LScaleCond1D3DWrapper
| Subroutine : | |||
| Temp : | real(DP), intent(inout)
| ||
| QVap : | real(DP), intent(inout)
| ||
| QH2OLiq : | real(DP), intent(inout)
| ||
| QH2OSol : | real(DP), intent(inout)
| ||
| Press : | real(DP), intent(in )
| ||
| PressLI : | real(DP), intent(in )
| ||
| PressUI : | real(DP), intent(in )
| ||
| DQH2OLiqDt : | real(DP), intent(out )
| ||
| DQH2OSolDt : | real(DP), intent(out )
|
大規模凝結スキームにより, 温度と比湿を調節します.
Adjust temperature and specific humidity by large scale condensation scheme.
subroutine LScaleCond1Grid( Temp, QVap, QH2OLiq, QH2OSol, Press, PressLI, PressUI, DQH2OLiqDt, DQH2OSolDt )
!
! 大規模凝結スキームにより, 温度と比湿を調節します.
!
! Adjust temperature and specific humidity by
! large scale condensation scheme.
!
! モジュール引用 ; USE statements
!
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav, CpDry, LatentHeat, LatentHeatFusion
! $ L $ [J kg-1] .
! 融解の潜熱.
! Latent heat of fusion
! 時刻管理
! Time control
!
use timeset, only: DelTime, TimeN, TimesetClockStart, TimesetClockStop
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoPut
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only: CalcQVapSat, CalcDQVapSatDTemp
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only : SaturateWatFraction
! 宣言文 ; Declaration statements
!
implicit none
real(DP), intent(inout):: Temp
! $ T $ . 温度. Temperature
real(DP), intent(inout):: QVap
! $ q $ . 比湿. Specific humidity
real(DP), intent(inout):: QH2OLiq
! Specific liquid water content
real(DP), intent(inout):: QH2OSol
! Specific ice content
real(DP), intent(in ):: Press
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP), intent(in ):: PressLI
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(in ):: PressUI
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(out ):: DQH2OLiqDt
!
! Tendency of H2O liquid mixing ratio
real(DP), intent(out ):: DQH2OSolDt
!
! Tendency of H2O ice mixing ratio
! 作業変数
! Work variables
!
real(DP):: DTempDtLsc
! 温度変化率.
! Temperature tendency
real(DP):: DQVapDtLsc
! 比湿変化率.
! Specific humidity tendency
real(DP):: QH2OVap0
! 調節前の比湿.
! Specific humidity before adjust.
real(DP):: QH2OLiq0
!
! Specific liquid water content before adjust.
real(DP):: QH2OSol0
!
! Specific liquid water content before adjust.
real(DP):: Temp0
! 調節前の温度.
! Temperature before adjust.
!
real(DP):: QH2OVapB
! 調節前の比湿.
! Specific humidity before adjust.
real(DP):: QH2OLiqB
!
! Specific liquid water content before adjust.
real(DP):: QH2OSolB
!
! Specific liquid water content before adjust.
real(DP):: TempB
! 調節前の温度.
! Temperature before adjust.
!
real(DP):: QVapSat
! 飽和比湿.
! Saturation specific humidity.
real(DP):: DQVapSatDTemp
! $ \DD{q_{\rm{sat}}}{T} $
real(DP):: DelTemp
! 調節による温度変化量.
! Temperature variation by adjustment
real(DP) :: WatFrac
real(DP) :: IceFrac
integer:: itr ! イテレーション方向に回る DO ループ用作業変数
! Work variables for DO loop in iteration direction
logical:: FlagProcess
! 実行文 ; Executable statement
!
! 初期化確認
! Initialization check
!
if ( .not. lscond_inited ) then
call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
end if
!!$ ! 計算時間計測開始
!!$ ! Start measurement of computation time
!!$ !
!!$ call TimesetClockStart( module_name )
! 調節前 "QVap", "Temp" の保存
! Store "QVap", "Temp" before adjustment
!
QH2OVap0 = QVap
QH2OLiq0 = QH2OLiq
QH2OSol0 = QH2OSol
Temp0 = Temp
! 調節
! Adjustment
!
! 飽和比湿計算
! Calculate saturation specific humidity
!
if ( FlagSatAdj ) then
Temp = Temp + ( LatentHeat * QH2OLiq + ( LatentHeat + LatentHeatFusion ) * QH2OSol ) / CpDry
QVap = QVap + QH2OLiq + QH2OSol
QH2OLiq = 0.0_DP
QH2OSol = 0.0_DP
else
! Pre-existing cloud water and ice are removed, since those are not
! responsible with condensation (assumption).
QH2OLiq = 0.0_DP
QH2OSol = 0.0_DP
end if
!
QVapSat = CalcQVapSat( Temp, Press )
!
if ( ( QVap / QVapSat ) >= CrtlRH ) then
FlagProcess = .true.
else
FlagProcess = .false.
end if
do itr = 1, ItrtMax
QH2OVapB = QVap
QH2OLiqB = QH2OLiq
QH2OSolB = QH2OSol
TempB = Temp
! 飽和比湿計算
! Calculate saturation specific humidity
!
QVapSat = CalcQVapSat ( Temp, Press )
DQVapSatDTemp = CalcDQVapSatDTemp( Temp, QVapSat )
! 飽和していたら, 温度と比湿の変化を計算
! Calculate tendency of temperature and humidity
! if moist is saturation.
!
if ( FlagProcess ) then
! Liquid water and ice fractions
call SaturateWatFraction( Temp, WatFrac )
IceFrac = 1.0_DP - WatFrac
! 温度の変化分をニュートン法で求める
! Calculate variation of temperature
!
!!$ DelTemp = &
!!$ & LatentHeatLocal &
!!$ & * ( z_QVap(k) - CrtlRH * z_QVapSat(k) ) &
!!$ & / ( CpDry + LatentHeatLocal * CrtlRH * z_DQVapSatDTemp(k) )
DelTemp = ( LatentHeat * QVap - LatentHeatFusion * QH2OSol + LatentHeatFusion * IceFrac * ( QVap + QH2OLiq + QH2OSol ) - ( LatentHeat + LatentHeatFusion * IceFrac ) * CrtlRH * QVapSat ) / ( CpDry + ( LatentHeat + LatentHeatFusion * IceFrac ) * CrtlRH * DQVapSatDTemp )
! 温度と比湿の調節
! Adjust temperature and specific humidity
!
Temp = Temp + DelTemp
QVap = CrtlRH * ( QVapSat + DQVapSatDTemp * DelTemp )
QH2OLiq = WatFrac * ( QH2OVapB + QH2OLiqB + QH2OSolB - QVap )
QH2OSol = IceFrac * ( QH2OVapB + QH2OLiqB + QH2OSolB - QVap )
end if
end do
if ( FlagSatAdj ) then
else
! Pre-existing cloud water and ice amount are restored.
QH2OLiq = QH2OLiq + QH2OLiq0
QH2OSol = QH2OSol + QH2OSol0
end if
! 比湿変化率, 温度変化率, 降水量の算出
! Calculate specific humidity tendency, temperature tendency,
! precipitation
!
DTempDtLsc = ( Temp - Temp0 ) / ( 2.0_DP * DelTime )
DQVapDtLsc = ( QVap - QH2OVap0 ) / ( 2.0_DP * DelTime )
DQH2OLiqDt = ( QH2OLiq - QH2OLiq0 ) / ( 2.0_DP * DelTime )
DQH2OSolDt = ( QH2OSol - QH2OSol0 ) / ( 2.0_DP * DelTime )
call LScaleCond1GridConsChk( Temp0, QH2OVap0, QH2OLiq0, QH2OSol0, Temp , QVap , QH2OLiq , QH2OSol )
!!$ ! 計算時間計測一時停止
!!$ ! Pause measurement of computation time
!!$ !
!!$ call TimesetClockStop( module_name )
end subroutine LScaleCond1Grid
| Subroutine : | |
| FlagSnow : | logical, intent(in) |
lscond モジュールの初期化を行います. NAMELIST#lscond_nml の読み込みはこの手続きで行われます.
"lscond" module is initialized. "NAMELIST#lscond_nml" is loaded in this procedure.
This procedure input/output NAMELIST#lscond_nml .
subroutine LScaleCondInit( FlagSnow )
!
! lscond モジュールの初期化を行います.
! NAMELIST#lscond_nml の読み込みはこの手続きで行われます.
!
! "lscond" module is initialized.
! "NAMELIST#lscond_nml" is loaded in this procedure.
!
! モジュール引用 ; USE statements
!
! NAMELIST ファイル入力に関するユーティリティ
! Utilities for NAMELIST file input
!
use namelist_util, only: namelist_filename, NmlutilMsg, NmlutilAryValid
! ファイル入出力補助
! File I/O support
!
use dc_iounit, only: FileOpen
! 種別型パラメタ
! Kind type parameter
!
use dc_types, only: STDOUT ! 標準出力の装置番号. Unit number of standard output
! 文字列操作
! Character handling
!
use dc_string, only: StoA
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoAddVariable
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only: SaturateInit
! 雲関系ルーチン
! Cloud-related routines
!
use cloud_utils, only : CloudUtilsInit
! 宣言文 ; Declaration statements
!
implicit none
logical, intent(in) :: FlagSnow
integer:: unit_nml ! NAMELIST ファイルオープン用装置番号.
! Unit number for NAMELIST file open
integer:: iostat_nml ! NAMELIST 読み込み時の IOSTAT.
! IOSTAT of NAMELIST read
! NAMELIST 変数群
! NAMELIST group name
!
namelist /lscond_nml/ QH2OFlucRatio, CrtlRH, ItrtMax, FlagSatAdj
!
! デフォルト値については初期化手続 "lscond#LSCondInit"
! のソースコードを参照のこと.
!
! Refer to source codes in the initialization procedure
! "lscond#LSCondInit" for the default values.
!
! 実行文 ; Executable statement
!
if ( lscond_inited ) return
! デフォルト値の設定
! Default values settings
!
QH2OFlucRatio = 0.2_DP
CrtlRH = 1.0_DP
ItrtMax = 3
FlagSatAdj = .false.
! NAMELIST の読み込み
! NAMELIST is input
!
if ( trim(namelist_filename) /= '' ) then
call FileOpen( unit_nml, namelist_filename, mode = 'r' ) ! (in)
rewind( unit_nml )
read( unit_nml, nml = lscond_nml, iostat = iostat_nml ) ! (out)
close( unit_nml )
call NmlutilMsg( iostat_nml, module_name ) ! (in)
if ( iostat_nml == 0 ) write( STDOUT, nml = lscond_nml )
end if
! Initialization of modules used in this module
!
! Initialization of modules used in this module
!
call SaturateInit
! 雲関系ルーチン
! Cloud-related routines
!
call CloudUtilsInit( FlagSnow )
! ヒストリデータ出力のためのへの変数登録
! Register of variables for history data output
!
call HistoryAutoAddVariable( 'DTempDtLsc', (/ 'lon ', 'lat ', 'sig ', 'time' /), 'large-scale condensation heating', 'K s-1' )
call HistoryAutoAddVariable( 'DQH2OVapDtLsc', (/ 'lon ', 'lat ', 'sig ', 'time' /), 'large-scale condensation moistening', 'kg kg-1 s-1' )
call HistoryAutoAddVariable( 'DQH2OLiqDtLsc', (/ 'lon ', 'lat ', 'sig ', 'time' /), 'large-scale H2O liquid production rate', 'kg kg-1 s-1' )
call HistoryAutoAddVariable( 'DQH2OSolDtLsc', (/ 'lon ', 'lat ', 'sig ', 'time' /), 'large-scale H2O solid production rate', 'kg kg-1 s-1' )
! 印字 ; Print
!
call MessageNotify( 'M', module_name, '----- Initialization Messages -----' )
call MessageNotify( 'M', module_name, ' QH2OFlucRatio = %f', d = (/ QH2OFlucRatio /) )
call MessageNotify( 'M', module_name, ' CrtlRH = %f', d = (/ CrtlRH /) )
call MessageNotify( 'M', module_name, ' ItrtMax = %d', i = (/ ItrtMax /) )
call MessageNotify( 'M', module_name, ' FlagSatAdj = %b', l = (/ FlagSatAdj /) )
call MessageNotify( 'M', module_name, '-- version = %c', c1 = trim(version) )
lscond_inited = .true.
end subroutine LScaleCondInit
| Subroutine : | |||
| xyz_Temp(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_QVap(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_QH2OLiq(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_QH2OSol(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(inout)
| ||
| xyz_Press(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(in)
| ||
| xyr_Press(0:imax-1, 1:jmax, 0:kmax) : | real(DP), intent(in)
| ||
| xyz_DQH2OLiqDt(0:imax-1,1:jmax,1:kmax) : | real(DP), intent(out)
| ||
| xyz_DQH2OSolDt(0:imax-1,1:jmax,1:kmax) : | real(DP), intent(out)
| ||
| xyz_CloudCover(0:imax-1, 1:jmax, 1:kmax) : | real(DP), intent(out), optional
| ||
| FlagOutput : | logical , intent(in ), optional
|
大規模凝結スキームにより, 温度と比湿を調節します.
Adjust temperature and specific humidity by large scale condensation scheme.
subroutine LScaleCondLL911D3DWrapper( xyz_Temp, xyz_QVap, xyz_QH2OLiq, xyz_QH2OSol, xyz_Press, xyr_Press, xyz_DQH2OLiqDt, xyz_DQH2OSolDt, xyz_CloudCover, FlagOutput )
!
! 大規模凝結スキームにより, 温度と比湿を調節します.
!
! Adjust temperature and specific humidity by
! large scale condensation scheme.
!
! モジュール引用 ; USE statements
!
! OpenMP
!
!$ use omp_lib
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav
! $ g $ [m s-2].
! 重力加速度.
! Gravitational acceleration
! 時刻管理
! Time control
!
use timeset, only: DelTime, TimeN, TimesetClockStart, TimesetClockStop
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoPut
! 宣言文 ; Declaration statements
!
implicit none
real(DP), intent(inout):: xyz_Temp (0:imax-1, 1:jmax, 1:kmax)
! $ T $ . 温度. Temperature
real(DP), intent(inout):: xyz_QVap (0:imax-1, 1:jmax, 1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP), intent(inout):: xyz_QH2OLiq(0:imax-1, 1:jmax, 1:kmax)
! Specific liquid water content
real(DP), intent(inout):: xyz_QH2OSol(0:imax-1, 1:jmax, 1:kmax)
! Specific ice content
real(DP), intent(in):: xyz_Press (0:imax-1, 1:jmax, 1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP), intent(in):: xyr_Press (0:imax-1, 1:jmax, 0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(out) :: xyz_DQH2OLiqDt(0:imax-1,1:jmax,1:kmax)
!
! Tendency of H2O liquid mixing ratio
real(DP), intent(out) :: xyz_DQH2OSolDt(0:imax-1,1:jmax,1:kmax)
!
! Tendency of H2O ice mixing ratio
real(DP), intent(out), optional :: xyz_CloudCover(0:imax-1, 1:jmax, 1:kmax)
!
! Cloud cover
logical , intent(in ), optional :: FlagOutput
!
! Flag for output
! 作業変数
! Work variables
!
integer :: js
integer :: je
integer :: nthreads
integer, allocatable :: a_js(:)
integer, allocatable :: a_je(:)
real(DP):: xyz_TempB (0:imax-1, 1:jmax, 1:kmax)
! $ T $ . 温度. Temperature
real(DP):: xyz_QVapB (0:imax-1, 1:jmax, 1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP):: xy_RainLsc (0:imax-1, 1:jmax)
! 降水量.
! Precipitation
real(DP):: xyz_DTempDtLsc (0:imax-1, 1:jmax, 1:kmax)
! 温度変化率.
! Temperature tendency
real(DP):: xyz_DQVapDtLsc (0:imax-1, 1:jmax, 1:kmax)
! 比湿変化率.
! Specific humidity tendency
real(DP) :: z_Temp (1:kmax)
! $ T $ . 温度. Temperature
real(DP) :: z_QVap (1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP) :: z_QH2OLiq(1:kmax)
! Specic liquid water content
real(DP) :: z_QH2OSol(1:kmax)
! Specic ice content
real(DP) :: z_Press (1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP) :: r_Press (0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP) :: z_DQH2OLiqDt(1:kmax)
!
! Tendency of H2O liquid mixing ratio
real(DP) :: z_DQH2OSolDt(1:kmax)
!
! Tendency of H2O ice mixing ratio
real(DP) :: z_CloudCover(1:kmax)
integer:: i ! 経度方向に回る DO ループ用作業変数
! Work variables for DO loop in longitude
integer:: j ! 緯度方向に回る DO ループ用作業変数
! Work variables for DO loop in latitude
integer:: k ! 鉛直方向に回る DO ループ用作業変数
! Work variables for DO loop in vertical direction
integer :: n
! 実行文 ; Executable statement
!
! 初期化確認
! Initialization check
!
if ( .not. lscond_inited ) then
call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
end if
! 計算時間計測開始
! Start measurement of computation time
!
call TimesetClockStart( module_name )
nthreads = 1
!$ nthreads = omp_get_max_threads()
!!$ !$ write( 6, * ) "Number of processors : ", omp_get_num_procs()
!!$ !$ write( 6, * ) "Number of threads : ", nthreads
allocate( a_js(0:nthreads-1) )
allocate( a_je(0:nthreads-1) )
do n = 0, nthreads-1
if ( n == 0 ) then
a_js(n) = 1
else
a_js(n) = a_je(n-1) + 1
end if
a_je(n) = a_js(n ) + jmax / nthreads - 1
if ( n + 1 <= mod( jmax, nthreads ) ) then
a_je(n) = a_je(n) + 1
end if
end do
!!$ !$OMP PARALLEL DEFAULT(PRIVATE) &
!!$ !$OMP SHARED( &
!!$ !$OMP nthreads, a_js, a_je, &
!!$ !$OMP imax, kmax, &
!!$ !$OMP xyz_TempB, xyz_QVapB, &
!!$ !$OMP xyz_Temp, xyz_QVap, xyz_QH2OLiq, xyz_QH2OSol, &
!!$ !$OMP xyz_Press, xyr_Press, &
!!$ !$OMP xyz_DQH2OLiqDt, xyz_DQH2OSolDt, &
!!$ !$OMP xyz_CloudCover, &
!!$ !$OMP xy_RainLsc, xyz_DTempDtLsc, xyz_DQVapDtLsc, DelTime &
!!$ !$OMP )
!!$
!!$ !$OMP DO
do n = 0, nthreads-1
js = a_js(n)
je = a_je(n)
if ( js > je ) cycle
do k = 1, kmax
do j = js, je
xyz_TempB(:,j,k) = xyz_Temp(:,j,k)
xyz_QVapB(:,j,k) = xyz_QVap(:,j,k)
end do
end do
do j = js, je
do i = 0, imax-1
do k = 1, kmax
z_Temp (k) = xyz_Temp (i,j,k)
z_QVap (k) = xyz_QVap (i,j,k)
z_QH2OLiq(k) = xyz_QH2OLiq(i,j,k)
z_QH2OSol(k) = xyz_QH2OSol(i,j,k)
z_Press (k) = xyz_Press (i,j,k)
end do
do k = 0, kmax
r_Press (k) = xyr_Press (i,j,k)
end do
call LScaleCondLL911D( z_Temp, z_QVap, z_QH2OLiq, z_QH2OSol, z_Press, r_Press, z_DQH2OLiqDt, z_DQH2OSolDt, z_CloudCover )
do k = 1, kmax
xyz_Temp (i,j,k) = z_Temp (k)
xyz_QVap (i,j,k) = z_QVap (k)
xyz_QH2OLiq (i,j,k) = z_QH2OLiq (k)
xyz_QH2OSol (i,j,k) = z_QH2OSol (k)
xyz_DQH2OLiqDt(i,j,k) = z_DQH2OLiqDt(k)
xyz_DQH2OSolDt(i,j,k) = z_DQH2OSolDt(k)
end do
if ( present( xyz_CloudCover ) ) then
do k = 1, kmax
xyz_CloudCover(i,j,k) = z_CloudCover(k)
end do
end if
end do
end do
! calculation for output
do j = js, je
xy_RainLsc(:,j) = 0.0_DP
do k = kmax, 1, -1
xy_RainLsc(:,j) = xy_RainLsc(:,j) + xyz_DQH2OLiqDt(:,j,k) * ( xyr_Press(:,j,k-1) - xyr_Press(:,j,k) ) / Grav
end do
end do
do k = 1, kmax
do j = js, je
xyz_DTempDtLsc(:,j,k) = ( xyz_Temp(:,j,k) - xyz_TempB(:,j,k) ) / ( 2.0_DP * DelTime )
xyz_DQVapDtLsc(:,j,k) = ( xyz_QVap(:,j,k) - xyz_QVapB(:,j,k) ) / ( 2.0_DP * DelTime )
end do
end do
end do
!!$ !$OMP END DO
!!$ !$OMP END PARALLEL
deallocate( a_js )
deallocate( a_je )
! ヒストリデータ出力
! History data output
!
if ( .not. present( FlagOutput ) ) then
call HistoryAutoPut( TimeN, 'DTempDtLsc' , xyz_DTempDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OVapDtLsc', xyz_DQVapDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OLiqDtLsc', xyz_DQH2OLiqDt )
call HistoryAutoPut( TimeN, 'DQH2OSolDtLsc', xyz_DQH2OSolDt )
else
if ( FlagOutput ) then
call HistoryAutoPut( TimeN, 'DTempDtLsc' , xyz_DTempDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OVapDtLsc', xyz_DQVapDtLsc )
call HistoryAutoPut( TimeN, 'DQH2OLiqDtLsc', xyz_DQH2OLiqDt )
call HistoryAutoPut( TimeN, 'DQH2OSolDtLsc', xyz_DQH2OSolDt )
end if
end if
! 計算時間計測一時停止
! Pause measurement of computation time
!
call TimesetClockStop( module_name )
end subroutine LScaleCondLL911D3DWrapper
| Subroutine : | |||
| z_Temp(1:kmax) : | real(DP), intent(inout)
| ||
| z_QVap(1:kmax) : | real(DP), intent(inout)
| ||
| z_QH2OLiq(1:kmax) : | real(DP), intent(inout)
| ||
| z_QH2OSol(1:kmax) : | real(DP), intent(inout)
| ||
| z_Press(1:kmax) : | real(DP), intent(in )
| ||
| r_Press(0:kmax) : | real(DP), intent(in )
| ||
| z_DQH2OLiqDt(1:kmax) : | real(DP), intent(out )
| ||
| z_DQH2OSolDt(1:kmax) : | real(DP), intent(out )
|
大規模凝結スキームにより, 温度と比湿を調節します.
Adjust temperature and specific humidity by large scale condensation scheme.
subroutine LScaleCond1D( z_Temp, z_QVap, z_QH2OLiq, z_QH2OSol, z_Press, r_Press, z_DQH2OLiqDt, z_DQH2OSolDt )
!
! 大規模凝結スキームにより, 温度と比湿を調節します.
!
! Adjust temperature and specific humidity by
! large scale condensation scheme.
!
! モジュール引用 ; USE statements
!
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav, CpDry, LatentHeat, LatentHeatFusion
! $ L $ [J kg-1] .
! 融解の潜熱.
! Latent heat of fusion
! 時刻管理
! Time control
!
use timeset, only: DelTime, TimeN, TimesetClockStart, TimesetClockStop
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoPut
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only: a_CalcQVapSat, a_CalcDQVapSatDTemp
! 宣言文 ; Declaration statements
!
implicit none
real(DP), intent(inout):: z_Temp (1:kmax)
! $ T $ . 温度. Temperature
real(DP), intent(inout):: z_QVap (1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP), intent(inout):: z_QH2OLiq(1:kmax)
! Specific liquid water content
real(DP), intent(inout):: z_QH2OSol(1:kmax)
! Specific ice content
real(DP), intent(in ):: z_Press (1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP), intent(in ):: r_Press (0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(out ):: z_DQH2OLiqDt(1:kmax)
!
! Tendency of H2O liquid mixing ratio
real(DP), intent(out ):: z_DQH2OSolDt(1:kmax)
!
! Tendency of H2O ice mixing ratio
! 作業変数
! Work variables
!
integer:: k ! 鉛直方向に回る DO ループ用作業変数
! Work variables for DO loop in vertical direction
! 実行文 ; Executable statement
!
! 初期化確認
! Initialization check
!
if ( .not. lscond_inited ) then
call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
end if
!!$ ! 計算時間計測開始
!!$ ! Start measurement of computation time
!!$ !
!!$ call TimesetClockStart( module_name )
do k = 1, kmax
call LScaleCond1Grid( z_Temp(k), z_QVap(k), z_QH2OLiq(k), z_QH2OSol(k), z_Press(k), r_Press(k-1), r_Press(k), z_DQH2OLiqDt(k), z_DQH2OSolDt(k) )
end do
!!$ ! 計算時間計測一時停止
!!$ ! Pause measurement of computation time
!!$ !
!!$ call TimesetClockStop( module_name )
end subroutine LScaleCond1D
| Subroutine : | |
| z_TempB(1:kmax) : | real(DP), intent(in) |
| z_QH2OVapB(1:kmax) : | real(DP), intent(in) |
| z_QH2OLiqB(1:kmax) : | real(DP), intent(in) |
| z_QH2OSolB(1:kmax) : | real(DP), intent(in) |
| z_Temp(1:kmax) : | real(DP), intent(in) |
| z_QH2OVap(1:kmax) : | real(DP), intent(in) |
| z_QH2OLiq(1:kmax) : | real(DP), intent(in) |
| z_QH2OSol(1:kmax) : | real(DP), intent(in) |
subroutine LScaleCond1DConsChk( z_TempB, z_QH2OVapB, z_QH2OLiqB, z_QH2OSolB, z_Temp , z_QH2OVap , z_QH2OLiq , z_QH2OSol )
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav, CpDry, LatentHeat, LatentHeatFusion
! $ L $ [J kg-1] .
! 融解の潜熱.
! Latent heat of fusion
real(DP), intent(in) :: z_TempB (1:kmax)
real(DP), intent(in) :: z_QH2OVapB(1:kmax)
real(DP), intent(in) :: z_QH2OLiqB(1:kmax)
real(DP), intent(in) :: z_QH2OSolB(1:kmax)
real(DP), intent(in) :: z_Temp (1:kmax)
real(DP), intent(in) :: z_QH2OVap (1:kmax)
real(DP), intent(in) :: z_QH2OLiq (1:kmax)
real(DP), intent(in) :: z_QH2OSol (1:kmax)
! Local variables
!
real(DP) :: ValB
real(DP) :: Val
real(DP) :: Ratio
integer :: k
do k = kmax, 1, -1
Val = CpDry * z_TempB(k) + LatentHeat * z_QH2OVapB(k) - LatentHeatFusion * z_QH2OSolB(k)
ValB = Val
Val = CpDry * z_Temp(k) + LatentHeat * z_QH2OVap(k) - LatentHeatFusion * z_QH2OSol(k)
Ratio = ( Val - ValB ) / ( Val + 1.0d-100 )
if ( abs( Ratio ) > 1.0d-10 ) then
call MessageNotify( 'M', module_name, 'Simplified condensate static energy is not conserved, %f.', d = (/ Ratio /) )
end if
end do
do k = kmax, 1, -1
Val = z_QH2OVapB(k) + z_QH2OLiqB(k) + z_QH2OSolB(k)
ValB = Val
Val = z_QH2OVap (k) + z_QH2OLiq (k) + z_QH2OSol (k)
Ratio = ( Val - ValB ) / ( Val + 1.0d-100 )
if ( abs( Ratio ) > 1.0d-10 ) then
call MessageNotify( 'M', module_name, 'H2O mass is not conserved, %f.', d = (/ Ratio /) )
end if
end do
end subroutine LScaleCond1DConsChk
| Subroutine : | |||
| z_Temp(1:kmax) : | real(DP), intent(inout)
| ||
| z_QVap(1:kmax) : | real(DP), intent(inout)
| ||
| z_QH2OLiq(1:kmax) : | real(DP), intent(inout)
| ||
| z_QH2OSol(1:kmax) : | real(DP), intent(inout)
| ||
| z_Press(1:kmax) : | real(DP), intent(in )
| ||
| r_Press(0:kmax) : | real(DP), intent(in )
| ||
| z_DQH2OLiqDt(1:kmax) : | real(DP), intent(out )
| ||
| z_DQH2OSolDt(1:kmax) : | real(DP), intent(out )
|
大規模凝結スキームにより, 温度と比湿を調節します.
Adjust temperature and specific humidity by large scale condensation scheme.
subroutine LScaleCond1D_BK( z_Temp, z_QVap, z_QH2OLiq, z_QH2OSol, z_Press, r_Press, z_DQH2OLiqDt, z_DQH2OSolDt )
!
! 大規模凝結スキームにより, 温度と比湿を調節します.
!
! Adjust temperature and specific humidity by
! large scale condensation scheme.
!
! モジュール引用 ; USE statements
!
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav, CpDry, LatentHeat, LatentHeatFusion
! $ L $ [J kg-1] .
! 融解の潜熱.
! Latent heat of fusion
! 時刻管理
! Time control
!
use timeset, only: DelTime, TimeN, TimesetClockStart, TimesetClockStop
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoPut
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only: a_CalcQVapSat, a_CalcDQVapSatDTemp
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only : SaturateWatFraction
! 宣言文 ; Declaration statements
!
implicit none
real(DP), intent(inout):: z_Temp (1:kmax)
! $ T $ . 温度. Temperature
real(DP), intent(inout):: z_QVap (1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP), intent(inout):: z_QH2OLiq(1:kmax)
! Specific liquid water content
real(DP), intent(inout):: z_QH2OSol(1:kmax)
! Specific ice content
real(DP), intent(in ):: z_Press (1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP), intent(in ):: r_Press (0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(out ):: z_DQH2OLiqDt(1:kmax)
!
! Tendency of H2O liquid mixing ratio
real(DP), intent(out ):: z_DQH2OSolDt(1:kmax)
!
! Tendency of H2O ice mixing ratio
! 作業変数
! Work variables
!
real(DP):: z_DTempDtLsc (1:kmax)
! 温度変化率.
! Temperature tendency
real(DP):: z_DQVapDtLsc (1:kmax)
! 比湿変化率.
! Specific humidity tendency
real(DP):: z_QH2OVap0 (1:kmax)
! 調節前の比湿.
! Specific humidity before adjust.
real(DP):: z_QH2OLiq0 (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_QH2OSol0 (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_Temp0 (1:kmax)
! 調節前の温度.
! Temperature before adjust.
!
real(DP):: z_QH2OVapB (1:kmax)
! 調節前の比湿.
! Specific humidity before adjust.
real(DP):: z_QH2OLiqB (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_QH2OSolB (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_TempB (1:kmax)
! 調節前の温度.
! Temperature before adjust.
!
real(DP):: z_QVapSat (1:kmax)
! 飽和比湿.
! Saturation specific humidity.
real(DP):: z_DQVapSatDTemp(1:kmax)
! $ \DD{q_{\rm{sat}}}{T} $
real(DP):: DelTemp
! 調節による温度変化量.
! Temperature variation by adjustment
real(DP) :: WatFrac
real(DP) :: IceFrac
integer:: k ! 鉛直方向に回る DO ループ用作業変数
! Work variables for DO loop in vertical direction
integer:: itr ! イテレーション方向に回る DO ループ用作業変数
! Work variables for DO loop in iteration direction
logical:: z_FlagProcess(1:kmax)
! 実行文 ; Executable statement
!
! 初期化確認
! Initialization check
!
if ( .not. lscond_inited ) then
call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
end if
!!$ ! 計算時間計測開始
!!$ ! Start measurement of computation time
!!$ !
!!$ call TimesetClockStart( module_name )
! 調節前 "QVap", "Temp" の保存
! Store "QVap", "Temp" before adjustment
!
z_QH2OVap0 = z_QVap
z_QH2OLiq0 = z_QH2OLiq
z_QH2OSol0 = z_QH2OSol
z_Temp0 = z_Temp
! 調節
! Adjustment
!
! 飽和比湿計算
! Calculate saturation specific humidity
!
if ( FlagSatAdj ) then
z_Temp = z_Temp + ( LatentHeat * z_QH2OLiq + ( LatentHeat + LatentHeatFusion ) * z_QH2OSol ) / CpDry
z_QVap = z_QVap + z_QH2OLiq + z_QH2OSol
z_QH2OLiq = 0.0_DP
z_QH2OSol = 0.0_DP
else
! Pre-existing cloud water and ice are removed, since those are not
! responsible with condensation (assumption).
z_QH2OLiq = 0.0_DP
z_QH2OSol = 0.0_DP
end if
!
z_QVapSat = a_CalcQVapSat( z_Temp, z_Press )
!
do k = 1, kmax
if ( ( z_QVap(k) / z_QVapSat(k) ) >= CrtlRH ) then
z_FlagProcess(k) = .true.
else
z_FlagProcess(k) = .false.
end if
end do
do itr = 1, ItrtMax
z_QH2OVapB = z_QVap
z_QH2OLiqB = z_QH2OLiq
z_QH2OSolB = z_QH2OSol
z_TempB = z_Temp
! 飽和比湿計算
! Calculate saturation specific humidity
!
z_QVapSat = a_CalcQVapSat ( z_Temp, z_Press )
z_DQVapSatDTemp = a_CalcDQVapSatDTemp( z_Temp, z_QVapSat )
do k = 1, kmax
! 飽和していたら, 温度と比湿の変化を計算
! Calculate tendency of temperature and humidity
! if moist is saturation.
!
if ( z_FlagProcess(k) ) then
! Liquid water and ice fractions
call SaturateWatFraction( z_Temp(k), WatFrac )
IceFrac = 1.0_DP - WatFrac
! 温度の変化分をニュートン法で求める
! Calculate variation of temperature
!
DelTemp = ( LatentHeat * z_QVap(k) - LatentHeatFusion * z_QH2OSol(k) + LatentHeatFusion * IceFrac * ( z_QVap(k) + z_QH2OLiq(k) + z_QH2OSol(k) ) - ( LatentHeat + LatentHeatFusion * IceFrac ) * CrtlRH * z_QVapSat(k) ) / ( CpDry + ( LatentHeat + LatentHeatFusion * IceFrac ) * CrtlRH * z_DQVapSatDTemp(k) )
! 温度と比湿の調節
! Adjust temperature and specific humidity
!
z_Temp(k) = z_Temp(k) + DelTemp
z_QVap(k) = CrtlRH * ( z_QVapSat(k) + z_DQVapSatDTemp(k) * DelTemp )
z_QH2OLiq(k) = WatFrac * ( z_QH2OVapB(k) + z_QH2OLiqB(k) + z_QH2OSolB(k) - z_QVap(k) )
z_QH2OSol(k) = IceFrac * ( z_QH2OVapB(k) + z_QH2OLiqB(k) + z_QH2OSolB(k) - z_QVap(k) )
end if
end do
end do
if ( FlagSatAdj ) then
else
! Pre-existing cloud water and ice amount are restored.
z_QH2OLiq = z_QH2OLiq + z_QH2OLiq0
z_QH2OSol = z_QH2OSol + z_QH2OSol0
end if
! 比湿変化率, 温度変化率, 降水量の算出
! Calculate specific humidity tendency, temperature tendency,
! precipitation
!
z_DTempDtLsc = ( z_Temp - z_Temp0 ) / ( 2.0_DP * DelTime )
z_DQVapDtLsc = ( z_QVap - z_QH2OVap0 ) / ( 2.0_DP * DelTime )
z_DQH2OLiqDt = ( z_QH2OLiq - z_QH2OLiq0 ) / ( 2.0_DP * DelTime )
z_DQH2OSolDt = ( z_QH2OSol - z_QH2OSol0 ) / ( 2.0_DP * DelTime )
call LScaleCond1DConsChk( z_Temp0, z_QH2OVap0, z_QH2OLiq0, z_QH2OSol0, z_Temp , z_QVap , z_QH2OLiq , z_QH2OSol )
!!$ ! 計算時間計測一時停止
!!$ ! Pause measurement of computation time
!!$ !
!!$ call TimesetClockStop( module_name )
end subroutine LScaleCond1D_BK
| Subroutine : | |
| TempB : | real(DP), intent(in) |
| QH2OVapB : | real(DP), intent(in) |
| QH2OLiqB : | real(DP), intent(in) |
| QH2OSolB : | real(DP), intent(in) |
| Temp : | real(DP), intent(in) |
| QH2OVap : | real(DP), intent(in) |
| QH2OLiq : | real(DP), intent(in) |
| QH2OSol : | real(DP), intent(in) |
subroutine LScaleCond1GridConsChk( TempB, QH2OVapB, QH2OLiqB, QH2OSolB, Temp , QH2OVap , QH2OLiq , QH2OSol )
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav, CpDry, LatentHeat, LatentHeatFusion
! $ L $ [J kg-1] .
! 融解の潜熱.
! Latent heat of fusion
real(DP), intent(in) :: TempB
real(DP), intent(in) :: QH2OVapB
real(DP), intent(in) :: QH2OLiqB
real(DP), intent(in) :: QH2OSolB
real(DP), intent(in) :: Temp
real(DP), intent(in) :: QH2OVap
real(DP), intent(in) :: QH2OLiq
real(DP), intent(in) :: QH2OSol
! Local variables
!
real(DP) :: ValB
real(DP) :: Val
real(DP) :: Ratio
integer :: k
Val = CpDry * TempB + LatentHeat * QH2OVapB - LatentHeatFusion * QH2OSolB
ValB = Val
Val = CpDry * Temp + LatentHeat * QH2OVap - LatentHeatFusion * QH2OSol
Ratio = ( Val - ValB ) / ( Val + 1.0d-100 )
if ( abs( Ratio ) > 1.0d-10 ) then
call MessageNotify( 'M', module_name, 'Simplified condensate static energy is not conserved, %f.', d = (/ Ratio /) )
end if
Val = QH2OVapB + QH2OLiqB + QH2OSolB
ValB = Val
Val = QH2OVap + QH2OLiq + QH2OSol
Ratio = ( Val - ValB ) / ( Val + 1.0d-100 )
if ( abs( Ratio ) > 1.0d-10 ) then
call MessageNotify( 'M', module_name, 'H2O mass is not conserved, %f.', d = (/ Ratio /) )
end if
end subroutine LScaleCond1GridConsChk
| Subroutine : | |||
| z_Temp(1:kmax) : | real(DP), intent(inout)
| ||
| z_QH2OVap(1:kmax) : | real(DP), intent(inout)
| ||
| z_QH2OLiq(1:kmax) : | real(DP), intent(inout)
| ||
| z_QH2OSol(1:kmax) : | real(DP), intent(inout)
| ||
| z_Press(1:kmax) : | real(DP), intent(in )
| ||
| r_Press(0:kmax) : | real(DP), intent(in )
| ||
| z_DQH2OLiqDt(1:kmax) : | real(DP), intent(out )
| ||
| z_DQH2OSolDt(1:kmax) : | real(DP), intent(out )
| ||
| z_CloudCover(1:kmax) : | real(DP), intent(out ) |
大規模凝結スキームにより, 温度と比湿を調節します.
Adjust temperature and specific humidity by large scale condensation scheme.
subroutine LScaleCondLL911D( z_Temp, z_QH2OVap, z_QH2OLiq, z_QH2OSol, z_Press, r_Press, z_DQH2OLiqDt, z_DQH2OSolDt, z_CloudCover )
!
! 大規模凝結スキームにより, 温度と比湿を調節します.
!
! Adjust temperature and specific humidity by
! large scale condensation scheme.
!
! モジュール引用 ; USE statements
!
! 物理定数設定
! Physical constants settings
!
use constants, only: Grav, CpDry, LatentHeat, LatentHeatFusion
! $ L $ [J kg-1] .
! 融解の潜熱.
! Latent heat of fusion
! 時刻管理
! Time control
!
use timeset, only: DelTime, TimeN, TimesetClockStart, TimesetClockStop
! ヒストリデータ出力
! History data output
!
use gtool_historyauto, only: HistoryAutoPut
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only: a_CalcQVapSat, a_CalcDQVapSatDTemp
! 飽和比湿の算出
! Evaluate saturation specific humidity
!
use saturate, only : SaturateWatFraction
! 宣言文 ; Declaration statements
!
implicit none
real(DP), intent(inout):: z_Temp (1:kmax)
! $ T $ . 温度. Temperature
real(DP), intent(inout):: z_QH2OVap (1:kmax)
! $ q $ . 比湿. Specific humidity
real(DP), intent(inout):: z_QH2OLiq(1:kmax)
! Specific liquid water content
real(DP), intent(inout):: z_QH2OSol(1:kmax)
! Specific ice content
real(DP), intent(in ):: z_Press (1:kmax)
! $ p $ . 気圧 (整数レベル).
! Air pressure (full level)
real(DP), intent(in ):: r_Press (0:kmax)
! $ \hat{p} $ . 気圧 (半整数レベル).
! Air pressure (half level)
real(DP), intent(out ):: z_DQH2OLiqDt(1:kmax)
!
! Tendency of H2O liquid mixing ratio
real(DP), intent(out ):: z_DQH2OSolDt(1:kmax)
!
! Tendency of H2O ice mixing ratio
real(DP), intent(out ):: z_CloudCover(1:kmax)
! 作業変数
! Work variables
!
real(DP):: z_DTempDtLsc (1:kmax)
! 温度変化率.
! Temperature tendency
real(DP):: z_DQH2OVapDtLsc (1:kmax)
! 比湿変化率.
! Specific humidity tendency
real(DP):: z_QH2OTot (1:kmax)
! 調節前の水量.
! Specific water content before adjust.
real(DP):: z_QH2OVap0 (1:kmax)
! 調節前の比湿.
! Specific humidity before adjust.
real(DP):: z_QH2OLiq0 (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_QH2OSol0 (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_Temp0 (1:kmax)
! 調節前の温度.
! Temperature before adjust.
!
real(DP):: z_QH2OVapB (1:kmax)
! 調節前の比湿.
! Specific humidity before adjust.
real(DP):: z_QH2OLiqB (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_QH2OSolB (1:kmax)
!
! Specific liquid water content before adjust.
real(DP):: z_TempB (1:kmax)
! 調節前の温度.
! Temperature before adjust.
!
real(DP):: z_QH2OVapSat (1:kmax)
! 飽和比湿.
! Saturation specific humidity.
real(DP):: z_DQH2OVapSatDTemp(1:kmax)
! $ \DD{q_{\rm{sat}}}{T} $
real(DP):: DelTemp
! 調節による温度変化量.
! Temperature variation by adjustment
real(DP) :: CoefA
real(DP) :: CoefB
real(DP) :: QH2OCond
real(DP):: z_QH2OTotFluc(1:kmax)
real(DP) :: WatFrac
real(DP) :: IceFrac
real(DP) :: QH2OVapSat
integer:: k ! 鉛直方向に回る DO ループ用作業変数
! Work variables for DO loop in vertical direction
integer:: itr ! イテレーション方向に回る DO ループ用作業変数
! Work variables for DO loop in iteration direction
logical:: z_FlagProcess(1:kmax)
! 実行文 ; Executable statement
!
! 初期化確認
! Initialization check
!
if ( .not. lscond_inited ) then
call MessageNotify( 'E', module_name, 'This module has not been initialized.' )
end if
!!$ ! 計算時間計測開始
!!$ ! Start measurement of computation time
!!$ !
!!$ call TimesetClockStart( module_name )
! 調節前 "QH2OVap", "Temp" の保存
! Store "QH2OVap", "Temp" before adjustment
!
z_QH2OVap0 = z_QH2OVap
z_QH2OLiq0 = z_QH2OLiq
z_QH2OSol0 = z_QH2OSol
z_Temp0 = z_Temp
! 調節
! Adjustment
!
z_QH2OTot = z_QH2OVap + z_QH2OLiq + z_QH2OSol
z_QH2OTotFluc = QH2OFlucRatio * z_QH2OTot
! 飽和比湿計算
! Calculate saturation specific humidity
!
!!$ z_QH2OVapSat = a_CalcQVapSat( z_Temp, z_Press )
!!$ !
!!$ do k = 1, kmax
!!$ if ( &
!!$ & ( z_QH2OVapSat(k) <= ( z_QH2OTot(k) + z_QH2OTotFluc(k) ) ) &
!!$ & .or. &
!!$ & ( ( z_QH2OVap(k) < z_QH2OVapSat(k) ) .and. &
!!$ & ( z_QH2OLiq(k) + z_QH2OLiq(k) > 0.0_DP ) ) &
!!$ & ) then
!!$ z_FlagProcess(k) = .true.
!!$ else
!!$ z_FlagProcess(k) = .false.
!!$ end if
!!$ end do
z_FlagProcess = .true.
do itr = 1, ItrtMax
z_QH2OVapB = z_QH2OVap
z_QH2OLiqB = z_QH2OLiq
z_QH2OSolB = z_QH2OSol
z_TempB = z_Temp
! 飽和比湿計算
! Calculate saturation specific humidity
!
z_QH2OVapSat = a_CalcQVapSat ( z_Temp, z_Press )
z_DQH2OVapSatDTemp = a_CalcDQVapSatDTemp( z_Temp, z_QH2OVapSat )
do k = 1, kmax
! 飽和していたら, 温度と比湿の変化を計算
! Calculate tendency of temperature and humidity
! if moist is saturation.
!
if ( z_FlagProcess(k) ) then
! Liquid water and ice fractions
call SaturateWatFraction( z_Temp(k), WatFrac )
IceFrac = 1.0_DP - WatFrac
if ( z_QH2OVapSat(k) < z_QH2OTot(k) - z_QH2OTotFluc(k) ) then
CoefA = z_QH2OTot(k) - z_QH2OVapSat(k)
CoefB = - z_DQH2OVapSatDTemp(k)
else if ( z_QH2OVapSat(k) < z_QH2OTot(k) + z_QH2OTotFluc(k) ) then
CoefA = ( z_QH2OTot(k) + z_QH2OTotFluc(k) - z_QH2OVapSat(k) )**2 / ( 4.0_DP * z_QH2OTotFluc(k) )
CoefB = - ( z_QH2OTot(k) + z_QH2OTotFluc(k) - z_QH2OVapSat(k) ) / ( 2.0_DP * z_QH2OTotFluc(k) ) * z_DQH2OVapSatDTemp(k)
else
CoefA = 0.0_DP
CoefB = 0.0_DP
end if
! 温度の変化分をニュートン法で求める
! Calculate variation of temperature
!
DelTemp = ( - LatentHeat * z_QH2OLiq(k) - ( LatentHeat + LatentHeatFusion ) * z_QH2OSol(k) + ( LatentHeat + LatentHeatFusion * IceFrac ) * CoefA ) / ( CpDry - ( LatentHeat + LatentHeatFusion * IceFrac ) * CoefB )
! 温度と比湿の調節
! Adjust temperature and specific humidity
!
z_Temp(k) = z_Temp(k) + DelTemp
QH2OCond = CoefA + CoefB * DelTemp
z_QH2OVap(k) = z_QH2OTot(k) - QH2OCond
z_QH2OLiq(k) = WatFrac * QH2OCond
z_QH2OSol(k) = IceFrac * QH2OCond
QH2OVapSat = z_QH2OVapSat(k) + z_DQH2OVapSatDTemp(k) * DelTemp
! It should be noted that, in general, z_QH2OVapSat(k) is not
! equal to QH2OVapSat.
if ( z_QH2OVapSat(k) < z_QH2OTot(k) - z_QH2OTotFluc(k) ) then
z_CloudCover(k) = 1.0_DP
else if ( z_QH2OVapSat(k) < z_QH2OTot(k) + z_QH2OTotFluc(k) ) then
z_CloudCover(k) = ( z_QH2OTot(k) + z_QH2OTotFluc(k) - QH2OVapSat ) / ( 2.0_DP * z_QH2OTotFluc(k) )
z_CloudCover(k) = max( min( z_CloudCover(k), 1.0_DP ), 0.0_DP )
else
z_CloudCover(k) = 0.0_DP
end if
else
z_CloudCover(k) = 0.0_DP
end if
end do
end do
! 比湿変化率, 温度変化率, 降水量の算出
! Calculate specific humidity tendency, temperature tendency,
! precipitation
!
z_DTempDtLsc = ( z_Temp - z_Temp0 ) / ( 2.0_DP * DelTime )
z_DQH2OVapDtLsc = ( z_QH2OVap - z_QH2OVap0 ) / ( 2.0_DP * DelTime )
z_DQH2OLiqDt = ( z_QH2OLiq - z_QH2OLiq0 ) / ( 2.0_DP * DelTime )
z_DQH2OSolDt = ( z_QH2OSol - z_QH2OSol0 ) / ( 2.0_DP * DelTime )
call LScaleCond1DConsChk( z_Temp0, z_QH2OVap0, z_QH2OLiq0, z_QH2OSol0, z_Temp , z_QH2OVap , z_QH2OLiq , z_QH2OSol )
!!$ ! 計算時間計測一時停止
!!$ ! Pause measurement of computation time
!!$ !
!!$ call TimesetClockStop( module_name )
end subroutine LScaleCondLL911D
| Constant : | |||
| version = ’$Name: $’ // ’$Id: lscond.f90,v 1.22 2015/03/11 04:53:25 yot Exp $’ : | character(*), parameter
|